The F8X M3/M4 Eventuri intake system was a culmination of months of dedicated design and development work. Here are some details of the development work and decisions which were made during the process:
The aim as always was to develop an intake in order to make the inlet track of the engine more efficient therefore allowing the engine to make more power. To do this Eventuri had to carefully balance inlet temperatures requirements with a smooth path for airflow. Clearly lower IATs is best for power but then ensuring the inlet track is smooth is equally as important to allow the turbos to draw in air with as little drag as possible.
All of Eventuri's main components are made from prepreg carbon fibre of the highest quality. Eventuri uses CF because it is a great heat insulator across its thickness. Other companies use Aluminium tubes etc which is a cheaper way of doing things but Aluminium is more than 400 times worse than CF at insulating the intake air from engine bay heat! So once the engine bay is heat soaked, metal tubes will get very hot and will heat up the inlet air as it travels through.
Filter Housings
The main component in Eventuri's intake systems and the thing which sets Eventuri apart from other intake companies is the Venturi housing which is a unique take on the regular "cone filter with heat shield" design. It is a Patent Pending system where the cone filter is reversed to decouple it from the narrower inlet/MAF tube and the actual housing acts to then shape the airflow smoothly down from the large opening to the smaller outlet to the MAF.
With the housing design completed to fit into the F8X engine bay, Eventuri then proceeded with the tubing which also holds the MAF sensors.
LHS Intake
Looking at the engine, the left side has a short convoluted pipe going from the OEM airbox to the turbo inlet tube. In order to use the Eventuri intake housing, the tube was redesigned, removing the ridges and importantly holding the MAF sensor.
To direct ambient air to the filter, a duct was designed which fits over the stock intake duct from the bumper. Initially this was designed as a closed duct to completely cover the mouth of the housing.
However, CFD analysis pointed to turbulence caused by the abrupt change in direction from the stock duct to the filter - on dyno testing this was proven as more power was gained by opening the top of this duct.
So this was redesigned and now the duct directs and saturates the filter opening with ambient air without causing a restriction - a balance between IATs and airflow:
Although now semi-open, IATs are still kept consistently low with the front scoops which saturate the area in front of the filters with ambient air.
Since the flexible stock tube has been removed and replaced with a rigid CF tube, some movement in the assembly was needed in line with engine rotation and vibrations. So a mounting bracket was designed to slot into the stock rubber airbox mount. The bracket has a stub at one end which sits in the rubber mount and allows for adequate movement.
RHS Intake
For the right side, the long tube from the Eventuri filter housing to the turbo inlet tube was redesigned. This longer tube has to clear the top of the radiator fan shroud but stay under the stock strut brace. In order to do so, like the stock tube, the tube transitions from circular at the connecting ends to oval in the middle for clearance. Importantly, a constant cross sectional area is maintained throughout the length downstream of the MAF sensor. By doing so the airflow maintains a constant velocity through the tube and the smooth geometric transitions help maintain laminar conditions.
Again, a duct was designed to capture ambient air from the stock ducts and direct the flow to the filters. Just like the analysis and testing carried out on the left side duct, opening the top of this duct was found to give the system more power. Again, the scoops then ensure cold air saturation at the filter mouth.
Front Air Scoops
The final components in this system are the front scoops - essential in the Eventuri system to direct ambient air to the ducts and then to the filters.
3D printed prototypes of the scoops in place capture the full area between the duct opening and the grills.
To illustrate the effectiveness of the scoop and duct designs, Eventuri put together a demonstration using a leaf blower to simulate airflow. The comparison was made between the Eventuri system and the stock system with the tops of the airboxes removed.
With the design completed, Eventuri moved onto production from Prepreg Carbon Fibre using the same weave as the OEM BMW M Performance 2x2 weave. Dyno testing was also carried out.